2005 TRIUMPH SPEED TRIPLE AND SPRINT ST INTEGRATED TAIL KIT INSTALLATION INSTRUCTIONS

download
1 ) PLACE THE TAIL LIGHT ASSEMBLY ON A SOFT SURFACE TO AVOID SCRATCHING OR DAMAGING THE LENS DURING THE CUTTING OPERATION. 2 ) POSITION YOUR CUTTING WHEEL AS SHOWN IN THE PICTURE TO THE LEFT WHERE THE CLEAR PART OF THE LENS MEETS THE BLACK PART. 3 ) PROCEED TO CUT INTO THE CLEAR LENS APPROXIMATELY HALF OF THE THICKNESS, ALL THE WAY AROUND THE PERIMETER OF THE LENS – BE SURE NOT TO CUT ALL THE WAY THROUGH BECAUSE IT WILL NOT GLUE BACK TOGETHER PROPERLY. SEE “TIPS FOR CUTTING YOUR LENS” BEFORE BEGINNING. TIPS FOR CUTTING YOUR LENS A) KEEP THE CUTTING WHEEL MOVING AND APPLY LIGHT PRESSURE. SITTING IN ONE SPOT WILL JUST MELT THE PLASTIC. WHEN YOU MAKE YOUR WAY AROUND THE ENTIRE PERIMETER, CLEAN ALL THE BURRED PLASTIC FROM AROUND THE EDGES AND FROM INSIDE THE GROOVE YOU’VE MADE. OPENING THE LENS 4 ) PLACE THE TIP OF A FLAT HEAD SCREWDRIVER IN THE GROOVE YOU HAVE CREATED. 5 ) GENTLY TWIST THE SCREWDRIVER TO CRACK THE GLUE ALONG THE GROOVE. NOTE: AS SOON AS YOU HEAR THE SOUND OF THE GLUE GIVING (A CRACK), MOVE THE SCREWDRIVER SLIGHTLY AND ADVANCE THE CRACK. SLOW AND STEADY IS THE NAME OF THE GAME HERE. IF YOU FIND A HARD SPOT, WEAKEN IT WITH THE CUTTING WHEEL AS NECESSARY. THE HARD PART IS OVER! YOU CAN RELAX NOW!
2 ©2005 Custom LED LLC. All Rights Reserved. 6 ) REMOVE THE SCREWS HOLDING THE STOCK LED BOARD TO THE HOUSING (YOU WILL BE REUSING THE SCREWS SO PUT THEM TO THE SIDE). 7 ) REMOVE THE STOCK LED ASSEMBLY FROM THE LENS HOUSING AND TURN IT FACE DOWN TO EXPOSE THE WIRING BEHIND. 8 ) SNIP OFF THE WIRES THAT CONNECT TO THE LED CIRCUIT BOARD AS CLOSE TO THE CIRCUIT BOARD AS POSSIBLE. 9 ) PLACE THE STOCK LED CIRCUIT BOARD OUT OF THE WAY. YOU WILL NO LONGER NEED THIS PART, DISPOSE OF IT AS YOU WISH. 10 ) DRILL A HOLE IN THE BACK SIDE OF THE ENCLOSURE IN THE LOCATION SHOWN IN FIGURE 10. THIS HOLE WILL BE USED TO ROUTE THE TWO BLINKER WIRES (RED AND WHITE) OUT OF THE ENCLOSURE. CHOOSE A BIT SIZE THAT IS ONLY AS LARGE AS NECESSARY TO FIT THE TWO WIRES THROUGH THE HOLE. WIRING UP YOUR CUSTOM LED BOARD PLACE YOUR CUSTOM LED INTEGRATED TAIL NEXT TO THE HOUSING, AND MATCH THE WIRE COLORS AS FOLLOWS: TRY TO HANDLE THE CIRCUIT BOARD AS LITTLE AS POSSIBLE AS FINGERPRINTS AND DIRT WILL HINDER THE PERFORMANCE. • • • • BLACK ON HARNESS TO 6″ BLACK ON CUSTOM LED BOARD • • • • GREEN ON HARNESS TO 6″ GREEN ON CUSTOM LED BOARD • • • • YELLOW ON HARNESS TO 6″ YELLOW ON CUSTOM LED BOARD USE THE THREE (3 OF 5) SUPPLIED ORANGE SPLICE CONNECTORS. PUSH THE TWO WIRES TO BE SPLICED TOGETHER INTO THE OPEN END. BE SURE TO PUSH THE WIRES ALL THE WAY IN (UNTIL YOU CAN SEE THEY HAVE REACHED THE OTHER SIDE). NOTE: THE SPLICE IS MORE RELIABLE IF THE WIRE IS NOT STRIPPED. BE SURE TO SNIP OFF THE BARE ENDS OF THE WIRES ON THE CUSTOM LED TAIL TO ENSURE THAT THERE IS INSULATION WHERE THE SPLICE WILL OCCUR. THE SUPPLIED SPLICE CONNECTORS AUTOMATICALLY DISPLACE THE INSULATION AS NECESSARY. ONCE YOU DOUBLE CHECK YOUR COLOR MATCHING AND ARE ABSOLUTELY SURE THAT THE WIRES ARE FULLY INSERTED INTO THE SPLICE CONNECTORS DO THE FOLLOWING: 11 ) SQUEEZE THE SPLICE CONNECTORS FIRMLY WITH PLIERS. VISUALLY INSPECT YOUR CONNECTIONS TO SEE THAT THEY HAVE BEEN SPLICED PROPERLY INSIDE. 12 ) RUN THE RED AND WHITE WIRES THROUGH THE HOLE YOU OPENED UP IN STEP 10. 13 ) POSITION YOUR CUSTOM LED BOARD IN PLACE AS SHOWN AND FASTEN THE BOARD USING THE SCREWS REMOVED FROM THE STOCK BOARD.